Suspension swap DIY

Re: Suspension swap DIY

Postby gippslandoffroad on Mon Jul 11, 2011 7:26 pm

interesting article - I alwasy remove top arm easier doesent alter aligmnet .
and always measure from bottom of rim to lip of guard and also do bump stop clearances most accurate form of suspension measurment used when doin R&D work among others :!:
gippslandoffroad
 
Posts: 3
Joined: Mon Jun 20, 2011 9:58 pm


 

Re: Suspension swap DIY

Postby saint on Mon Aug 01, 2011 7:29 pm

Thanks for the article.
Hoping for a bit of advice.
I'm about to put Dobinson's on my 09 ML (manual with one piece shaft)
I noticed you used the 100kg to GVM (Medium) rear springs.
I was thinking about going for the 350kg to GVM (Heavy Duty)
How do yours ride? Have you loaded it up yet with the boat on the back as well?
How did it handle it?
Also, did you go for the heavy duty on the front? How's that?
Would you change anything if you did it again?
Any suggestions would be greatly appreciated.
Once again, great article.
saint
 
Posts: 19
Joined: Sun Jan 18, 2009 5:42 pm
Location: Nambucca Heads NSW

Re: Suspension swap DIY

Postby snowman on Tue Aug 02, 2011 8:19 am

saint wrote:Thanks for the article.
Hoping for a bit of advice.
I'm about to put Dobinson's on my 09 ML (manual with one piece shaft)
I noticed you used the 100kg to GVM (Medium) rear springs.
I was thinking about going for the 350kg to GVM (Heavy Duty)
How do yours ride? Have you loaded it up yet with the boat on the back as well?
How did it handle it?
Also, did you go for the heavy duty on the front? How's that?
Would you change anything if you did it again?
Any suggestions would be greatly appreciated.
Once again, great article.


i don't even know what spring i have on the back (it is Dobi) :? so can't help there much although i do have a steel canopy and rear /side bars for permanent weight.

i do have the harder dobi front spring and can advise that it is the way to go if you run a bar and winch (or maybe dual batt) but without the winch (i.e. steel bar only) it is probably too stiff and runs a bit high.

Martin at Dobinsons can assist and i am pretty sure Ultimate will supply matched shocks even for Dobi springs if you specifically ask for them.
This car is like a bad drug habit. It is taking all my money and time, my family are concerned, but new mods just feel sooooooo good.
User avatar
snowman
Platinum Subscriber
 
Posts: 12031
Joined: Sat Feb 07, 2009 10:59 pm
Location: Toongabbie, NSW

Re: Suspension swap DIY

Postby ultimate on Tue Aug 02, 2011 10:57 am

interesting article - I alwasy remove top arm easier doesent alter aligmnet .
and always measure from bottom of rim to lip of guard and also do bump stop clearances most accurate form of suspension measurment used when doin R&D work among others


You should always do a wheel alignment after modifying the suspension regardless of what parts you remove during the install. Any change in height will throw out the alignment.

At lot of the measurements on this site are taken from the centre of the wheel to the guard. That way it's easy to compare heights regardless of rim size and is still accurate.
The Team at
Australian Ultimate Suspension Pty. Ltd
Phone: +612 9618 7674
http://www.ultimatesuspension.com.au YouTube Facebook
Designers, Manufacturers and Installers of performance aftermarket suspension for Cars, Trucks and 4wds
User avatar
ultimate
 
Posts: 2380
Joined: Tue Oct 06, 2009 12:43 pm

Re: Suspension swap DIY

Postby saint on Tue Aug 02, 2011 12:09 pm

Tex wrote:Saint if your question is for Subi_man he doesn't get on here much anymore. You could try PM'ing Greedy who also has Dobinsons. :D


Thanks Tex.
saint
 
Posts: 19
Joined: Sun Jan 18, 2009 5:42 pm
Location: Nambucca Heads NSW

Re: Suspension swap DIY

Postby saint on Tue Aug 02, 2011 12:13 pm

snowman wrote:
saint wrote:Thanks for the article.
Hoping for a bit of advice.
I'm about to put Dobinson's on my 09 ML (manual with one piece shaft)
I noticed you used the 100kg to GVM (Medium) rear springs.
I was thinking about going for the 350kg to GVM (Heavy Duty)
How do yours ride? Have you loaded it up yet with the boat on the back as well?
How did it handle it?
Also, did you go for the heavy duty on the front? How's that?
Would you change anything if you did it again?
Any suggestions would be greatly appreciated.
Once again, great article.


i don't even know what spring i have on the back (it is Dobi) :? so can't help there much although i do have a steel canopy and rear /side bars for permanent weight.

i do have the harder dobi front spring and can advise that it is the way to go if you run a bar and winch (or maybe dual batt) but without the winch (i.e. steel bar only) it is probably too stiff and runs a bit high.

Martin at Dobinsons can assist and i am pretty sure Ultimate will supply matched shocks even for Dobi springs if you specifically ask for them.


Thanks Snowman, will probably go with the heavy duty back and front. We really load the car up when travelling (tow a boat with off road trailer as well). Have done trips with the car sitting low due to load and it's not fun!
saint
 
Posts: 19
Joined: Sun Jan 18, 2009 5:42 pm
Location: Nambucca Heads NSW

Re: Suspension swap DIY

Postby Mattstruck on Thu Aug 04, 2011 6:42 pm

Just finished my Ultimate 2" kit.

Just wanted to thank Subi for a great article. Also just a small tip.

When putting in the front strut, place it in its final position and put the front (or closest) nut on the strut top on just a few turns.
So it is hanging by that one nut.
Then put your upper control arm back on and the bolts that hold it (they fit: bolt inside and nuts on outside) back in place.
Then go about doing the other 2 bolts and tighening them up.

If you dont do this and you tighten the 3 strut top bolts you cant get the upper control arm bolts through the control arm (unless you reverse the bolts) as the spring is in the way.
Found this out the hard way. Read: had to pull it back apart. :x

Recommend anyone planning this mod to pay the money for the struts to come pre-assembled.
Brendan sent them out pre fabbed and its just too easy!
Makes a bast8rd of a job easy and acheivable by one person.
I actually found the front end easier than the rear because of this.

I have MN with factory diff lock. I recommend that you just watch the air lines AND brake lines AND electrical connections when dropping the diff. They get VERY tight and stressed.
I think I will need to lengthen the brakes but the air and electrical... Thats all for another day :lol:

Finally, you will need TALL car stands as you must jack the body up high enough to get the wheels off the ground at the rear. My car stands were put on top of ------ so they were high enough to support the body.
Cant tell you what I put the stands on cos it really was dodgy and in breach of OHS standards :o :o :o
Didnt like it but had 2 jacks and 2 car stands so wasnt too bad :?

One question for Brendan:
What grease type should I be putting into the shackles - what do you recommend/use?
Mod talk:
Sometimes indecipherable to the average Civillian. Example:
Homer:
I clearly remember Joe stating categorically that he prefers it in the bottom
Joe:
I didn't say it was better in the bottom, I just said it was easier and quicker.
User avatar
Mattstruck
 
Posts: 2844
Joined: Fri Nov 19, 2010 7:47 pm
Location: Melbourne

Re: Suspension swap DIY

Postby GLX-R Alex on Sun Oct 16, 2011 6:52 pm

The torque setting is FT
User avatar
GLX-R Alex
 
Posts: 504
Joined: Mon Jun 08, 2009 4:06 pm

Re: Suspension swap DIY

Postby General Pershing on Sat Nov 12, 2011 7:51 pm

Mattstruck wrote:
Finally, you will need TALL car stands as you must jack the body up high enough to get the wheels off the ground at the rear. My car stands were put on top of ------ so they were high enough to support the body.
Cant tell you what I put the stands on cos it really was dodgy and in breach of OHS standards :o :o :o
Didnt like it but had 2 jacks and 2 car stands so wasnt too bad :?


Im doing mine now, im using milk crates.




































......lol just kidding.

I had trouble dropping the front lower control arms low enough to re mount the bottom strut bolt, had to get a bar and lever it down while i had 2 spring compressors on mounted 120degreed apart, then i had to use a ratchet strap to pull the bottom of the shock inwards, towards the mount. I'll try the other sde tomorrow.
General Pershing
 
Posts: 37
Joined: Sat Oct 08, 2011 9:47 am

Re: Suspension swap DIY

Postby jn5555 on Sat Feb 11, 2012 7:31 pm

Just wondering does the top wishbone need to be removed at all? replacing front shocks with standard.

if it is removed does that effect wheel alignment,camber etc?

thanks
John

ps thanks for posting, huge help.
jn5555
 
Posts: 1
Joined: Sat Feb 11, 2012 6:19 pm

Re: Suspension swap DIY

Postby DoubleD on Sat Nov 24, 2012 2:57 pm

Just a quick thanks to everyone especially Subi for putting this together.

I put in my suspension last night & this was good
to have a read of before I got into it.

One thing I had a little trouble with was getting the upper ball joint back in
place to put the 3 bolts in. Even jacking up the lower control arm I couldn't
get the ball joint close enough for the 3 bolts to get started.
So I ended up using my slide clamp, which worked a treat to compress them together.

I also agree with above, bolt the upper control arm up before mounting the lower
strut bolt, that & the clamp made doing the second strut a lot easier!

DD
User avatar
DoubleD
 
Posts: 243
Joined: Wed Mar 07, 2012 6:25 am

Re: Suspension swap DIY

Postby DoubleD on Sat Nov 24, 2012 3:02 pm

Click to view larger picture
User avatar
DoubleD
 
Posts: 243
Joined: Wed Mar 07, 2012 6:25 am

Re: Suspension swap DIY

Postby salt36 on Sat Nov 24, 2012 3:56 pm

jn5555 wrote:Just wondering does the top wishbone need to be removed at all? replacing front shocks with standard.

if it is removed does that effect wheel alignment,camber etc?

thanks
John

ps thanks for posting, huge help.


I have found removing the top wishbone completely makes the strut replacement a lot easier.

Should not affect wheel alignment.... it would be advisable to get a wheel alignment done when doing any works to the suspension though, I do, Bob Jane $50 8-) they do a good job too !
User avatar
salt36
Valued Contributor
 
Posts: 6381
Joined: Sun May 16, 2010 9:54 am
Location: Shepparton VIC

Re: Suspension swap DIY

Postby tom149835 on Mon Dec 24, 2012 1:29 pm

Has anyone got some advice on fitting the tail shaft spacer. In can only get about a 10mm gap between the tail shaft and diff to fit the approx. 25mm spacer. I am also concerned if I do manage to get it in that it will be putting to much pressure on the diff an gear box.
tom149835
 
Posts: 15
Joined: Sat Mar 31, 2012 5:33 pm

Re: Suspension swap DIY

Postby Bigbirdalx on Mon Sep 02, 2013 11:50 am

Just to bump this. Did anyone need to trim back the bump stop at the front, i found i had to take 10-15mm off the one at the control arm?
If im posting, im either on the toilet, at work or both
User avatar
Bigbirdalx
 
Posts: 677
Joined: Tue Oct 30, 2012 7:19 am
Location: northside of brisbane

Re: Suspension swap DIY

Postby NowForThe5th on Mon Sep 02, 2013 2:25 pm

There is no need to remove or trim the bump stops. I had mine in and out at least 4 times with various HD coils. It's a tight fit but not impossible.
Chris

If work is so terrific, why do they have to pay us to do it?
User avatar
NowForThe5th
Moderator
 
Posts: 9242
Joined: Sun Jun 15, 2008 2:00 pm
Location: Holt, ACT

Re: Suspension swap DIY

Postby bazzashadow on Sun Sep 15, 2013 6:24 am

gowie77 wrote:
tassie_ml wrote:could someone post up the torque settings for this install....thanks ;)


http://ftp.users.on.net/~holmes2804/Triton%20suspension/

Click on the above link, then click on the files ending in .PNG and it shows all the torque settings. Awesome post Subiman was really helpful.



Really helpful having all these torque settings, but what is the torque for the one bolt at the baet of the strut assembly in the front as well as the 3 bolts right at the top?
User avatar
bazzashadow
 
Posts: 20
Joined: Thu Apr 04, 2013 7:44 pm

Re: Suspension swap DIY

Postby Kingbrown on Mon Sep 16, 2013 12:37 pm

The three nuts at the top of the tower are 44Nm.
The bolt for bottom of the strut is 105Nm.
Kingbrown
Platinum Subscriber
 
Posts: 59
Joined: Wed Apr 18, 2012 2:31 pm

Re: Suspension swap DIY

Postby Witty9 on Fri Oct 11, 2013 7:23 pm

Thanks heaps bud. Top stuff
Witty9
 
Posts: 17
Joined: Sun Feb 17, 2013 2:24 pm

Re: Suspension swap DIY

Postby brodical on Thu Nov 07, 2013 8:04 am

Any one know of hand what size spanner is required for the 2 bolts on the uca???
Cheers
Choices we make not the chances we take determine who we are...
User avatar
brodical
 
Posts: 976
Joined: Mon Dec 05, 2011 5:49 pm
Location: Gippsland vic

.

Postby TUF909 on Thu Nov 07, 2013 8:10 am

.
Last edited by TUF909 on Thu Feb 27, 2014 8:23 am, edited 1 time in total.
Sam.

Shed: http://www.newtriton.net/myshed.php?view=1&id=3584

Build thread: viewtopic.php?f=51&t=17609

People who think they know everything are a great annoyance to those of us who do.
User avatar
TUF909
 
Posts: 920
Joined: Mon May 20, 2013 6:53 am
Location: Sunshine coast, Qld

Re: Suspension swap DIY

Postby brodical on Thu Nov 07, 2013 8:24 am

Thanks man appreciate it ..is there a chance there n imperial size if it was a bit loose? Or def metric? Maybe 3/4
Choices we make not the chances we take determine who we are...
User avatar
brodical
 
Posts: 976
Joined: Mon Dec 05, 2011 5:49 pm
Location: Gippsland vic

.

Postby TUF909 on Thu Nov 07, 2013 8:31 am

.
Last edited by TUF909 on Thu Feb 27, 2014 8:23 am, edited 1 time in total.
Sam.

Shed: http://www.newtriton.net/myshed.php?view=1&id=3584

Build thread: viewtopic.php?f=51&t=17609

People who think they know everything are a great annoyance to those of us who do.
User avatar
TUF909
 
Posts: 920
Joined: Mon May 20, 2013 6:53 am
Location: Sunshine coast, Qld

Re: Suspension swap DIY

Postby brodical on Thu Nov 07, 2013 8:47 am

Sweet yep 3/4 fits little bit snugger ....mine are metric too ..jst bought a 3/4 for a dollar lol
Choices we make not the chances we take determine who we are...
User avatar
brodical
 
Posts: 976
Joined: Mon Dec 05, 2011 5:49 pm
Location: Gippsland vic

Re: Suspension swap DIY

Postby Kingbrown on Thu Nov 07, 2013 4:28 pm

For the DIY'ers, there's a little snippet that I noticed in the Challenger workshop manual:
A 'Steering Sensor Calibration' is needed after a wheel alignment has been done (it's a MUT3 exercise).
Presumably this is so that the ASC wizardry and its associated sensors can work their magic correctly.
Kingbrown
Platinum Subscriber
 
Posts: 59
Joined: Wed Apr 18, 2012 2:31 pm

PreviousNext

Return to Suspension

Who is online

Users browsing this forum: No registered users and 1 guest