Carbon build - up its everyone’s problem.

What were your warranty claims and recall information

Re: Carbon build - up its everyone’s problem.

Postby CharlieH11 on Thu Jul 18, 2019 10:15 pm

Hi,

I’ve just bought a 2011 GLR turbo diesel dual cab auto with 134000km on the clock. Have read a lot of different opinions in regards to EGR blocks, catch cans ect. I was wondering if anyone could give me the best alternative preventative method? Or if there actually is a need to do anything at all.
CharlieH11
 
Posts: 4
Joined: Thu Jul 18, 2019 10:04 pm


 

Re: Carbon build - up its everyone’s problem.

Postby explorer.dave on Thu Jul 18, 2019 10:55 pm

You could try reading through the thread, that will give you all the answers.
Better to be silent and thought a fool than open your mouth and remove all doubt.[

[b]Penrith Panthers 2021..Finally :roll:


Posts should be like mini skirts, long enough to cover the subject matter, but short enough to keep things interesting
User avatar
explorer.dave
Platinum Subscriber
 
Posts: 977
Joined: Wed Dec 18, 2013 9:32 am
Location: South Lake, Perth

Re: Carbon build - up its everyone’s problem.

Postby Longranger1 on Fri Jul 19, 2019 11:31 am

A 2K Ohm resistor in series with the thermistor in the airbox is the simplest solution. A single pair cable connected each side of the resistor can be connected to a hidden switch in the cab to reinstate the egr valve if required.
The voices in my head may not be real, but they do have some damned good ideas.

If it's feral, it's in peril.

MN turbo lag? What lag??

99% of lawyers give the rest a bad name.
User avatar
Longranger1
Platinum Subscriber
 
Posts: 2255
Joined: Wed May 26, 2010 7:37 pm
Location: Townsville NQ

Re: Carbon build - up its everyone’s problem.

Postby veight on Mon Aug 26, 2019 1:22 pm

Can anyone provide a picture of the upper and lower manifold ?
I have a upper manifold and have cleaned it , can i get a picture of the lower manifold to send to a wrecker ? showing it on the engine ? / pulled part if possible.
veight
 
Posts: 104
Joined: Sun Oct 10, 2010 5:06 pm
Location: Darwin NT

Re: Carbon build - up its everyone’s problem.

Postby Ausgamer on Mon Jun 29, 2020 12:16 pm

Hey all,
I'm trying to get my inlet manifold off my mn 2.5. I have removed all the bolts but still can't get this manifold off. I gave it a little tap with a rubber mallet but the little bugger is refusing to go.
Is there anything I am missing or is there any DIY guides available apart from the l200 Russian site(which is what I have been using) and the 4x4earth site.
Ausgamer
 
Posts: 17
Joined: Sun Jan 15, 2017 9:05 pm
Location: Mount Gambier, SA

Re: Carbon build - up its everyone’s problem.

Postby Longranger1 on Mon Jun 29, 2020 2:14 pm

Check for a missed bolt (or 2).
The voices in my head may not be real, but they do have some damned good ideas.

If it's feral, it's in peril.

MN turbo lag? What lag??

99% of lawyers give the rest a bad name.
User avatar
Longranger1
Platinum Subscriber
 
Posts: 2255
Joined: Wed May 26, 2010 7:37 pm
Location: Townsville NQ

Re: Carbon build - up its everyone’s problem.

Postby DibbyDibbyDJ on Mon Jun 29, 2020 3:24 pm

What about the 2 nuts right at the back?

6 long bolts (+ 1 that stays in manifold)
2 medium ones from nearer bulkhead
3 shorter ones from between intakes
1 short bolt going horizontally under manifold, just under front of inlet
2 10mm head size going from pipes to manifold
2024 Outlander

mitsubishi-forums.com
DibbyDibbyDJ
 
Posts: 461
Joined: Mon Oct 07, 2019 8:16 pm

Re: Carbon build - up its everyone’s problem.

Postby Ausgamer on Sun Jul 12, 2020 10:20 pm

Got it guys! Thanks for your help. It was so bad!
Ausgamer
 
Posts: 17
Joined: Sun Jan 15, 2017 9:05 pm
Location: Mount Gambier, SA

Re: Carbon build - up its everyone’s problem.

Postby viking shippy on Tue Jul 14, 2020 7:45 pm

NowForThe5th wrote:This has been discussed before but, again, two things:

    1. Funny how he makes the assertion that the temperature sensor controls, or is used in other engine management functions but doesn't, or can't actually say what these are.
    2. Towards the end the real purpose of the video becomes apparent. That is to sell his ECU tuning service.

The reality is that changing that signal is, at least on the MN and ML, the best and safest way to achieve prevention of the EGR from operating and thereby clogging the inlet manifold.

For the MQ the situation is quite different. The signal from that sensor is used in other engine management functions which is why there hasn't yet been a simple solution developed that works.
so do you recomend i dont use the elextonic block on a MR ? 5th


Sent from my iPhone using Tapatalk
User avatar
viking shippy
 
Posts: 3233
Joined: Sun Sep 19, 2010 5:16 pm

Re: Carbon build - up its everyone’s problem.

Postby NowForThe5th on Wed Jul 15, 2020 5:36 am

No, but be aware that it may have 'side effects'.
Chris

If work is so terrific, why do they have to pay us to do it?
User avatar
NowForThe5th
Moderator
 
Posts: 9239
Joined: Sun Jun 15, 2008 2:00 pm
Location: Holt, ACT

Re: Carbon build - up its everyone’s problem.

Postby viking shippy on Wed Jul 15, 2020 7:01 pm

NowForThe5th wrote:No, but be aware that it may have 'side effects'.
do you care to elaborate?


Sent from my iPhone using Tapatalk
User avatar
viking shippy
 
Posts: 3233
Joined: Sun Sep 19, 2010 5:16 pm

Re: Carbon build - up its everyone’s problem.

Postby DibbyDibbyDJ on Wed Jul 15, 2020 7:55 pm

Engines not stopping straight away.
Running lean due to info to ECU being adjusted by device
Exhaust gas temperature increasing.
poor fuel ecomomy


The MQ and MR are a entirely different generation of DPF and EGR compared to ML and MN. The system has improved greatly, with little or no soot clogging up the manifolds.

A catch can is always a good idea though
2024 Outlander

mitsubishi-forums.com
DibbyDibbyDJ
 
Posts: 461
Joined: Mon Oct 07, 2019 8:16 pm

Re: Carbon build - up its everyone’s problem.

Postby viking shippy on Sat Jul 18, 2020 4:10 pm

thanks fellas


Sent from my iPhone using Tapatalk
User avatar
viking shippy
 
Posts: 3233
Joined: Sun Sep 19, 2010 5:16 pm

Re: Carbon build - up its everyone’s problem.

Postby illuminateddan on Sun Feb 07, 2021 3:11 pm

Thanks for the how-to!! I'm a first-time triton owner of a 2006 ML and this walkthrough was awesome for my first tinker. Although it wasn't *that* gunked, it now runs beautifully, especially with an oil and filter change to clear out any gunk getting into the engine. Engine runs at 100+ RP<M less in idle now.

Thanks again, I'll be watching this forum from now on! :D :D
illuminateddan
 
Posts: 1
Joined: Sat Feb 06, 2021 9:24 am

Previous

Return to Warranty/Recalls

Who is online

Users browsing this forum: No registered users and 8 guests