The Drawers Thread - Show Us Yours Here

Want to show off what you've done to your rig? or have a custom project to show? Post it up here!

Re: The Drawers Thread - Show Us Yours Here

Postby willsyjp on Sun Sep 18, 2016 7:07 pm

peterkiwi wrote:Have you got any photos of them installed kxboss? id like to install these in my ML with retaining the tub liner.


Yes me too. Do they fit with the ML with tub liner
willsyjp
 
Posts: 1
Joined: Sat Jul 26, 2014 8:05 pm


 

Re: The Drawers Thread - Show Us Yours Here

Postby Mudme on Mon Oct 17, 2016 4:10 am

Some pics?
User avatar
Mudme
 
Posts: 468
Joined: Mon Jul 16, 2012 7:51 pm
Location: Officer victoria

Re: The Drawers Thread - Show Us Yours Here

Postby Sav on Sun Oct 30, 2016 11:31 am

I just installed my Titan drawers yesterday.. easy as check out my build thread if u want to see some pics of install

For those who have installed what have you done about wings?

Im struggling to find matching carpet

Sent from my SM-G930F using Tapatalk
Sav
 
Posts: 139
Joined: Sun Apr 12, 2015 1:41 pm

Re: The Drawers Thread - Show Us Yours Here

Postby KMsMK on Fri Nov 04, 2016 5:58 pm

Gday all, I've been sneaking around here for some time now, but never posted. Love the all the info too. I'm in the middle of making my drawer system. For runners I've used boat trailer nylon lengths from bcf, cut down for both the drawer and the fridge slide. I noticed that if there is a good load in the drawers that it is a bit harder to use. After an epiphany I realized that MR SHEEN works wonders at minimising the friction. So thought I would share with thise others with nylon strips for runners.
KMsMK
 
Posts: 1
Joined: Mon Jul 29, 2013 3:34 pm

Re: The Drawers Thread - Show Us Yours Here

Postby snakesoup on Sat Nov 05, 2016 5:37 pm

silicon spray would probably be the go ! dust doesn't stick to it
User avatar
snakesoup
 
Posts: 1115
Joined: Sun Feb 02, 2014 2:24 pm

rear drawers

Postby daves on Wed Jan 09, 2019 4:05 pm

has anyone fitted the 4wd supercentre draws and had any issues with them,iam thinking of getting the 1300 long
daves
 
Posts: 9
Joined: Fri Nov 11, 2016 5:16 pm

Re: The Drawers Thread - Show Us Yours Here

Postby Camma119 on Mon Jan 28, 2019 5:18 pm

So I’ve been through this whole topic and can’t find what I’m after. I just purchased the titan rear drawers with wings for my mn triton, has anyone purchased and installed these. Seems that the wheel arches sit higher than the drawer unit so that the wings won’t work. Or i have to try and cut them around the arches which will look messy. Any info guys?
Camma119
 
Posts: 1
Joined: Mon Jan 28, 2019 5:07 pm

Re: The Drawers Thread - Show Us Yours Here

Postby Enid_Triton on Mon Jun 10, 2019 5:09 pm

I know this is an old post but I just went through the same ordeal with the Titan Drawers I purchased for my MN.
"It will fit straight in" he said, "Really easy to install" he said, "It only takes about 2 hours" he said.
Well it didn't fit straight in, and it wasn't easy, and it took me the whole day.

To get the drawers & wing kit to fit in neatly you have to put 30mm thick spacers under the frame that are also wide enough to spread the load over the ribs in tub liner or it will eventually flatten out.
Then cut 100mm off the rear wing angle bracket so it will sit flat on the guard. You don't shorten it, you just remove the thickness where it is folded down in a U shape for strength. Then it sits perfectly on top of the guard without any movement.
Then shape the wing lids to fit the side profiles of the tub.
Then extend & shape the carpeted ends by 100mm wide & 40mm in depth (at the bottom) with metal, I used 2 mm thick aluminum sheet. There is enough carpet left over from the wings to do this.
Also, you can put a piece of carpeted aluminum angle at the Cab end on top of the drawers to stop any crap falling down into the 20mm gap that ends up being left there. I had to buy more Utility carpet from Bunning's for this, a close match too.
I also neatened it up at the front with a piece of aluminum angle & glued carpet onto it & then cut to fit the tub profile, Otherwise you can see underneath because it is now raised by 30mm.
Anyway, it takes heaps longer than it should and you have to do a fair bit of custom fabricating to get it into a MN Triton, but it turns out pretty good in the long run.
Here is mine:
Click to view larger picture
Click to view larger picture
Click to view larger picture
User avatar
Enid_Triton
 
Posts: 35
Joined: Fri Dec 14, 2018 1:38 pm
Location: Brisbane

Previous

Return to Member Build Ups

Who is online

Users browsing this forum: No registered users and 1 guest