Egr blanking plate in mq???

[jerrah]

SPVi have been through our own development on this model and we do have plug and play solution but due to our current work load, they have not been officially released.

Has anyone successfully purchased one of these plug in units yet?

[jerrah]

https://chiptuning.com.au/products-page/egr_module/

Pajero Sports (2.4ltr) and MQ Triton EGR OFF Modules are not released as yet.

THANKS FOR NOT EMAILING US AS TO WHEN THESE WILL BE AVAILABLE.

Does Chiptuning = Tony?

[explorer.dave]

ChipTuning are an agent for SPVi which is Tony.

[Cowboy Dave]

More a reseller than an agent, but same same I guess.

[FERALTRITON16]

hey guys I am new to the site but just wondering aswell did u have any fault codes being thrown up as a result of using the egr plate cheers

[NowForThe5th]

Freal, read this thread, starting from near the end of Page 2.

[jerrah]

Cable installed - 60-80kmh full throttle flat road - Initial spike 23 psi boost settling at 19-20psi max.
A loss of 4psi and I can feel it.

I'd hazard a guess that since the resistor is on the air temp sensor the ECU purposely limits boost when the air temp is high to prevent engine damage, and it would assume the air temp is always high.

Interested to see this Tony mod if it's ever released. I doubt a plate with a hole in it is as effective as a complete block, and I'm curious to know whether the EGR flow is a requirement to get the DPF working correctly.

[Joemn]

Anyone found out if Tony's mod is available yet?? Or any other mods been tested lately?

Sent from my SM-G930F using Tapatalk

[jerrah]

I received an email reply a few weeks ago stating that it isn't in production yet and there would be an announcement when it was available.

[Joemn]

I received an email reply a few weeks ago stating that it isn't in production yet and there would be an announcement when it was available.

Thanks..

Sent from my SM-G930F using Tapatalk

[jerrah]

I haven't fitted an EGR blank but I've looked a few that are available on eBay. I've noticed they're all quite thick compared to the original gasket on the EGR. It would seem that if the blank is too thick it would cause alignment issues with the EGR pipe and not seal 100%?

Which EGR plates have people been using? Was it of similar thickness to the gasket? Did you leave the original gasket in or remove it?

[Sky Miner]

I pulled the gasket out n made a stainless copy out of it and put that in as the replacement, pretty much the same thickness, ran one on my old MN for 70k's n never had any prob's and no prob's with the MQ either

[Spaceman]

I have a ERG plate with a hole no fault codes or issues, all good. Are there any MQ drivers out there who are running a full blank plate?(no hole) If so how long before it put up a fault code? and from what hear they don't go into limp mode. I had a Ranger that would put P401 with a full EGR blank plate in, what I found is if the air intake senor #2 went above 50c the fault would clear. This sensor was located where the intake and the EGR gases would meet at the manifold. Placed a resistor to tell the ECU the temp was above 55c no more P401. There must be a way ECU detects EGR flow on the MQ's and I see there is a EGR temp sensor which in the manual has resistance to temp chart. Is this the way they detect flow ? and I wonder if a resistor across the plug would stop the fault code

[Spaceman]

The EGR plate I got off EBay is 1.5mm thick and have seen them advertised up to 2mm thick. It appears to seal OK but i don't over tighten the bolts due to the pipe being cast not wanting to crack it. Going to find some thin stainless and make a copy

[Greytriton]

I run a no hole EGR blanking plate for the last 6 months, basically from new.

Coasting down hills with no throttle will induce a CEL. Clear able with the scan gauge.

[RHKTriton]

Your fault codes are probably from exceeding a certain vacuum level in the inlet manifold.

A solid blank after the egr cooler (offers protection against anything, inc water coming down this path) and electronic defeat of the egr offers the best solution. Also stops wear and tear on the egr unit.

Then a catch can to complete the package.

[Spaceman]

I would of thought it would fault code P401 no EGR flow

[glowplug]

can someone post where they are fitting the plates with small hole, i looked back through the thread but is a little conflicting of where to actually fit the plate. and do you put the gasket back in?

[Spaceman]

Where the EGR pipe meets the intake manifold, i left the gasket out and there was no leaks.

[glowplug]

The loom from Munji anyone using it might be better to get the loom and just plug it in

[YTO]

Just want to let all mq owners know that chip tuning now selling the module. Just placed an order today. I'm not sure who makes them didn't ask. Hope this help.

[jerrah]

Just want to let all mq owners know that chip tuning now selling the module. Just placed an order today. I'm not sure who makes them didn't ask. Hope this help.

Ill be interested to see what you receive!

[ls2cruiser]

The question is " is this the module that Tony is going to produce at some stage" ? It has to be different for the MQ

[explorer.dave]

The question is " is this the module that Tony is going to produce at some stage" ? It has to be different for the MQ

Mate, that question was answered 3 posts up, yes, the module has been produced by Tony, you can now purchase through chiptuning, link below FYI

https://chiptuning.com.au/products-page/egr_module/

[YTO]

Received the module today from chip tuning, thanks to Robert. Will try to install sometime soon.
Too bad I don't own a scanner to monitor so not sure what to expect.